Weidmuller WI-I/O-9-U2: Wireless Mesh I/O & Gateway User Instrukcja Użytkownika Strona 81
- Strona / 126
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
80
Netmask
The subnet mask for the destination network.
Interface
Choose the interface to use for the route. Selections are Radio,
Ethernet or Any – Default is Any.
Gateway
Specifies the IP address of the next-hop router for the specified
destination.
Enabled
Check this box to enable the rule. You can Uncheck the box to
disable a routing rule without needing to re-enter the information at
a later time.
Save Changes
Save changes to non-volatile memory. The module will need to be
restarted before the changes take effect.
Save Changes
and Reset.
Save settings to non-volatile memory, and reboot WI-I/O 9-U2.
Once the module has completed the reboot sequence, all changes
are in effect.
4.4.4 Radio Settings
Select the “Radio” Menu to change the following configuration parameters. If a change
is made, you need to select “Save Changes” to retain the changes. Changes will not
take effect until the unit is reset.
Figure 64 – Radio Configuration Screen
Radio Settings
Network
Address
A unique address that is used to differentiate one wireless system
from another, All radios that are required to communicate within the
system will need to have the same Network Address
Messages received with a different System Address will be ignored.
It is used to prevent Cross-talk between systems.
Valid values are between 0 and 32768
Encryption
Select 64 bit WEIDMULLER proprietary encryption or 128, 192 or
256 bit AES encryption from the drop down list.
Encryption Key
Up to 32 characters are available for Encryption key.
Message
The Message Signature is a section of data at the head of the radio
- Industrial Wireless MESH I/O 1
- WI-I/O 9-U2 MESH I/O 1
- 804.794.2877 Main 2
- 804.794.0252 Fax 2
- Industry Canada: 3
- FCC Notice: 4
- Hazardous Location Notices: 5
- IMPORTANT Notice: 6
- TABLE OF CONTENTS 7
- TABLE OF FIGURES 11
- Chapter 1 - Introduction 13
- 1.2 Module Structure 15
- 1.3 Getting Started 16
- Chapter 2 - Installation 17
- 2.2.2 Expansion I/O Supply 19
- 2.2.3 Internal I/O 20
- 2.2.4 Grounding 20
- 2.3 Radio 21
- 2.4 Antenna 22
- Yagi antennas 26
- 2.5 Connections 27
- WI-IO 9-U2 28
- “Factory Boot” switch 29
- USB Host port 29
- Dipswitches 29
- Front panel connections 30
- Figure 16 - Fail-Safe State 33
- 2.5.5 Analog Inputs 34
- Single Ended Voltage Inputs 36
- 2.5.6 Analog Outputs 37
- Chapter 3 - Operation 38
- Digital Inputs 39
- Digital Outputs 39
- ETHERNET 40
- LINK100M 40
- 3.3 System Design 41
- 3.3.4 Design for Failures 42
- Fail-to-transmit alarm 43
- Fail-to-receive alarm 43
- 3.4 WIBMesh 44
- Chapter 4 - Configuration 46
- Figure 23 – Network Settings 47
- Figure 24 - Ping 47
- Figure 26 - IP Gateway Mode 49
- Figure 27 - Default Gateway 49
- Figure 28 -IP Address Range 49
- Figure 29 - Routing Rule 50
- 4.3 Module Configuration 51
- Re-Open Previous Project 52
- 4.3.2 Configuration Screens 53
- 4.3.3 Project Screen 54
- 4.3.4 Adding Units 54
- Unit Details 55
- 4.3.5 Mappings 56
- Write Mapping 57
- Gather Scatter Mapping 57
- Read Mappings 57
- Example configuration 60
- 4.3.7 Address Map 61
- 4.3.9 I/O Configuration 62
- Pulsed Outputs 63
- Analog Inputs 64
- Analog Outputs 65
- Adding modules 65
- (selected on the rotary 66
- 4.3.11 Failsafe Blocks 67
- “Invalid” register state 68
- 4.3.12 Sensitivity Blocks 69
- 4.3.13 Serial Configuration 70
- Serial - Expansion I/O 71
- 4.3.14 Modbus Configuration 72
- Mapping parameters 73
- Modbus TCP Mapping Examples 75
- Modbus RTU Master 75
- Modbus RTU 76
- Master Example 76
- 4.4 Web based Configuration 77
- Figure 62 - Neighbour RSSI 79
- 4.4.3 IP Routing 80
- 4.4.4 Radio Settings 81
- 4.4.5 Mesh Fixed Routes 82
- Example #1 83
- Example #2 84
- Writing Configuration File 87
- System Log File 87
- Reading Configuration File 87
- Figure 73 - Format USB 88
- Figure 74 - Quick Format 88
- Figure 75 - Firmware Files 88
- Figure 76- firmware version 89
- Product Reconfiguration 90
- Demonstration Mode 91
- Feature Licence Keys 91
- Chapter 5 - Diagnostics 92
- 5.1.1 Watchdog Error Log 93
- 5.2 Connectivity (WibMesh) 95
- 5.4 Neighbour RSSI (WibMesh) 97
- Figure 87 - Multipath Fading 98
- Trace Route 100
- 5.7 Monitor Comms 103
- Chapter 6 - Specifications 108
- “Output Coils” 112
- “Input Bits” 112
- “Input Registers” 113
- “Holding Registers” 114
- 115 116
- 118 119
- 119 120
- 120 121
- 121 122
- 122 123
- 123 124
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji