Weidmuller WI-I/O-9-U2: Wireless Mesh I/O & Gateway User Instrukcja Użytkownika Strona 105
- Strona / 126
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
104
5.7.3 WibNet – Monitor Comms
Figure 96 - WibNet Monitor Comms
The above screen shot shows the Received and Transmitted WibNet data frames.
The Table below shows an excerpt from the above screen shot.
Data frames are displayed similar to the WibMesh Monitor Radio Comms except the
data is a different format.
Below that is another table explaining each of the field within the data frame.
Time
Source IP
Dest IP
Len
Type
Seq
Ack
Dest
Cnt
Val
03:02:45.073629
192.168.2.146.51891
192.168.2.143.4370
7
WRITE
9
1
1
11111110
03:02:45.075693
192.168.2.143.56678
192.168.2.146.4370
1
ACK
9
Time
Message Time Stamp – Time from when module was last started
Header
Displays if message is a receive (In) or a transmit (Out) as well as the
type and size of the Ethernet frame
Source IP
Originating or Source IP Address
Dest IP
Destination IP Address
Len
Total length of WEIDMULLER data
Type
Type of Message, i.e. Write, Read, Gather /Scatter, Etc.
Seq
Sequence number of the message
Ack
Indicates if the Weidmuller data frame is configured to acknowledge or
not acknowledged. This is configured in each mapping.
Dest
I/O address at the destination – where the data will be written to or read
from.
Cnt
Total I/O count from the “dest” address above
Val
Data values – the number of value will depend on I/O count.
- Industrial Wireless MESH I/O 1
- WI-I/O 9-U2 MESH I/O 1
- 804.794.2877 Main 2
- 804.794.0252 Fax 2
- Industry Canada: 3
- FCC Notice: 4
- Hazardous Location Notices: 5
- IMPORTANT Notice: 6
- TABLE OF CONTENTS 7
- TABLE OF FIGURES 11
- Chapter 1 - Introduction 13
- 1.2 Module Structure 15
- 1.3 Getting Started 16
- Chapter 2 - Installation 17
- 2.2.2 Expansion I/O Supply 19
- 2.2.3 Internal I/O 20
- 2.2.4 Grounding 20
- 2.3 Radio 21
- 2.4 Antenna 22
- Yagi antennas 26
- 2.5 Connections 27
- WI-IO 9-U2 28
- “Factory Boot” switch 29
- USB Host port 29
- Dipswitches 29
- Front panel connections 30
- Figure 16 - Fail-Safe State 33
- 2.5.5 Analog Inputs 34
- Single Ended Voltage Inputs 36
- 2.5.6 Analog Outputs 37
- Chapter 3 - Operation 38
- Digital Inputs 39
- Digital Outputs 39
- ETHERNET 40
- LINK100M 40
- 3.3 System Design 41
- 3.3.4 Design for Failures 42
- Fail-to-transmit alarm 43
- Fail-to-receive alarm 43
- 3.4 WIBMesh 44
- Chapter 4 - Configuration 46
- Figure 23 – Network Settings 47
- Figure 24 - Ping 47
- Figure 26 - IP Gateway Mode 49
- Figure 27 - Default Gateway 49
- Figure 28 -IP Address Range 49
- Figure 29 - Routing Rule 50
- 4.3 Module Configuration 51
- Re-Open Previous Project 52
- 4.3.2 Configuration Screens 53
- 4.3.3 Project Screen 54
- 4.3.4 Adding Units 54
- Unit Details 55
- 4.3.5 Mappings 56
- Write Mapping 57
- Gather Scatter Mapping 57
- Read Mappings 57
- Example configuration 60
- 4.3.7 Address Map 61
- 4.3.9 I/O Configuration 62
- Pulsed Outputs 63
- Analog Inputs 64
- Analog Outputs 65
- Adding modules 65
- (selected on the rotary 66
- 4.3.11 Failsafe Blocks 67
- “Invalid” register state 68
- 4.3.12 Sensitivity Blocks 69
- 4.3.13 Serial Configuration 70
- Serial - Expansion I/O 71
- 4.3.14 Modbus Configuration 72
- Mapping parameters 73
- Modbus TCP Mapping Examples 75
- Modbus RTU Master 75
- Modbus RTU 76
- Master Example 76
- 4.4 Web based Configuration 77
- Figure 62 - Neighbour RSSI 79
- 4.4.3 IP Routing 80
- 4.4.4 Radio Settings 81
- 4.4.5 Mesh Fixed Routes 82
- Example #1 83
- Example #2 84
- Writing Configuration File 87
- System Log File 87
- Reading Configuration File 87
- Figure 73 - Format USB 88
- Figure 74 - Quick Format 88
- Figure 75 - Firmware Files 88
- Figure 76- firmware version 89
- Product Reconfiguration 90
- Demonstration Mode 91
- Feature Licence Keys 91
- Chapter 5 - Diagnostics 92
- 5.1.1 Watchdog Error Log 93
- 5.2 Connectivity (WibMesh) 95
- 5.4 Neighbour RSSI (WibMesh) 97
- Figure 87 - Multipath Fading 98
- Trace Route 100
- 5.7 Monitor Comms 103
- Chapter 6 - Specifications 108
- “Output Coils” 112
- “Input Bits” 112
- “Input Registers” 113
- “Holding Registers” 114
- 115 116
- 118 119
- 119 120
- 120 121
- 121 122
- 122 123
- 123 124
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji